Products
FINISH
PRODUCT DESCRIPTION
KKS® TILEBOND C2-S1 is one component, cement-polymer based, ready-mixed tile adhesive.
This product meets the technical requirements of C2 group S1 class cementitious tile adhesive mortar - high-grade cementitious tile adhesive mortar according to TCVN 7899-1:2008 (or ISO 13007: 2004).
ADVANTAGE
• High impact resistance: reduce damage to tile caused by impact.
• High adhesive strength.
• Increased polymer helps to minimize peeling and problems in application.
• Resistant to vibration and structural movement.
• Long-time workability, which allows adjustment after applying.
• Modified cement-polymer based tile adhesive mortar, with economic efficiency
USES
• Can be used for both indoor and outdoor.
• Can be used in wet area such as: bathrooms, kitchens.
• Can be applied on glazed and unglazed tiles.
• Suitable for most tiles, bricks...
APPLICATION
SURFACE PREPARATION
Concrete surface must be clean, sound, level and uncontaminated by oil or grease. Absorbent substrates must be pre-wetted to saturated surface dry condition.
MIXING
The mixing ratio is about 25% compare to the amount of mortar.
Mixing the product by trowel until the mixture is consistency. In larger quantities, use the low speed mixer.
COVERAGE
About 2.5 - 3.0 kg/m2/2mm
APPLYING
Using specialized towel to apply a thin coat, then apply the bond with suitable thickness, normally from 2 mm to 4mm.
The consumption depends on the surface roughness and the roughness of substrate as well as on the size of the tiles and the placing technique (simple placing or back-buttering).
CLEANING
Clean tools and equipment immediately after finishing work and before the material becomes harden with clean water.
PRODUCT AND TECHNICAL DATA
|
Form |
A mixture of cement - polymer with selective aggregates and additives. |
|
Color |
Grey powder |
|
Packaging |
25 kg/bag |
|
Density |
≈ 1.60 kg/l (bulk density of powder) ≈ 1.90 kg/l (density of fresh mortar) |
|
Mixing ratio |
Water/ Powder = 25% (part by weight) |
|
Consumption |
1 bag yields approx. 14.5 litters of mortar 69 bags (25kg) for 1m3 of mortar |
|
Coverage |
≈ 7-8 m2 per 25kg bag (based on 2mm mortar thickness) |
|
Adhesion strength in standard condition (after 28 days) |
≥ 1.0 N/mm2 (TCVN 7899-2:2008) |
|
Adhesion strength after water immersion (at 28 days age) |
≥ 1.0 N/mm2 (TCVN 7899-2:2008) |
|
Adhesion strength after heat aging (at 28 days age) |
≥ 1.0 N/mm2 (TCVN 7899-2:2008) |
|
Transverse deformation (after 28 days) |
≥ 2.5 mm (ISO 13007-2:2013) |
|
Initial setting time |
> 180 minutes |
|
Pot life |
60 minutes (65% r.H, at 27oC) |
|
Adjustment allowance time |
30 minutes |
|
Waiting time before grouting |
7 - 8 hours (Depending on temperature) 24 hours (For Floor) Open to full traffic after 14 days |
|
Application temperature |
8 - 40oC |
STORAGE / SHELF LIFE
KKS® TILEBOND C2-S1 must be stored in dry, covered place. Unpacked, undamaged packaging has 9 months of shelf life.
SAFETY INFORMATION
KKS® TILEBOND C2-S1 contains cement which can cause skin irritation. Wear eye protection and respirator. The product is not dangerous when transported. Non-toxic, non-flammable. Dispose of in accordance with local regulations. For more information, please refer to the latest Product Safety Data Sheet.
