WATERPROOFING

KKS® ELASTSEAL 332

Price: Contact us

DESCRIPTION
KKS® ELASTSEAL 332
is a highly elastic waterproofing membrane, self-drying, water repellent polyurethane based. Application in liquid form, when hardened it forms seamless continuous film, excellent adhesion to most types of surfaces.
ADVANTAGES
•    One-component, easy-to-use product that can be applied with existing tools such as roller, brushes, pressure spraying.
•    Good elasticity so not be peeled, cracked, ensure waterproofing even the plaster surface inside has cross-foot crack because of thermal expansion.
•    Good adhesion on a variety of surface types.
•    Seamless membranes without lining.
•    Alkali resistance, water resistance and weather resistance. especially for UV rays, suitable with tropical areas.
•    Non-toxic, non-flammable, environmentally friendly.
•    Not moldy
•    High solid content, low VOC.
USES    
KKS® ELASTSEAL 332
is used for surface’s waterproofing of following construction category:
•    Waterproofing for the exposed concrete roof, cement tiles, terrazzo tiles.
•    Waterproofing for dome, roof terrace, sunbathing balcony and balustrade wall.
•    Wet areas such as waterproofing lining before placing tiles in bathrooms, kitchens.
•    Waterproofing over old roofs that need to be upgraded.
APPLICATION
SURFACE PREPARATION

The concrete substrate must be hard enough (28 days) and cleaned, free from oil, grease and other contaminants. A pull-off strength of at least 1.5 N/mm2. Maximum substrate moisture content of 5%, maximum air humidity 85%. Seal surface damage such as pore, porosity... with KKS® MORTATOP to have a flat surface. At the water leakage, KKS® WATERPLUG 302 should be used to completely prevent. 
Metallic surfaces such as iron, steel must be cleaned of rust.
It is recommended that all corners be chamfered with mortar so that waterproofing membranes can be swept and bonded.
APPLICATION
Normally primer is not required, but if many pore, non-flat surfaces, apply KKS® PRIMER S160 with 0.2 - 0.3 kg / m2. After application of the primer, surface should be covered with waterproofing within 24 hours to avoid contamination.
Step 1: Stir the paint barrel to get uniform color. Avoid creating air bubbles.
Step 2: Use a smooth roller, brush or spray machine to apply 2 coats. With airless spray equipment, such as Graco X45 piston pump, parameters set is: pressures 200-250 bar, nozzle 0.38-0.33 mm, spray angle 50 - 80o.
IF THE REINFORCEMENT LAYER DOES NOT IN USE:
•    KKS® ELASTSEAL 332
is applied in two coats with the ratio is 0.6 - 0.9 kg/ m2/ layer
IF THE REINFORCEMENT LAYER IS USED:
•    Use brush or roller application KKS® ELASTSEAL 332 as a base coat. Apply KKS® FLEXSHEET reinforcement on wet substrates, ensuring that the reinforcement layer is evenly covered and stretched flat without wrinkles. The overlap between the two coating is at least 50 mm. Constructed with a norm of 1.6 kg / m2 
•    Apply the second coat immediately with a norm of 0.8 kg / m2.
NOTICE
•    KKS® ELASTSEAL 332
is not use at the place where standing water or continuous submerged in water or the surface moisture content increase.
•    Do not work in rain conditions. If it is raining during construction, should stop to cover the area of construction being affected directly from rain water.
•    Self-drying material, no watering maintenance required after application.
•    Apply a second coat after the surface of first coat has dried.
CLEANNING OF TOOLS
Clean water, tools and equipment immediately after application and before the material is harden.
PRODUCT DATA

Base

Polyurethane plastic

Form

Semi-fluid liquid

Color

White / Grey

Packaging

20 kg/pail

Density

≈ 1.27 ± 0.03 kg/l (20oC) (ASTM D1475)

Solid content

≈ 65 ± 5 (ASTM D2369)

Elongation at break

≈ 450 % (ASTM D412)

Tensile Strength

≈ 3 N/mm2 (ASTM D412)

Tear Strength

> 11 (N/mm2) (ASTM D624)

Adhesive Strength

≈ 1.5 N/mm2 (ASTM D4541)

Hardness

≈ 70 (Shore D – Hardness ASTM D2240)

Flash point

Non-flammable (water based)

UV resistance

Pass (no impair after 3000 hours)

Toxicity

Non-toxic

Temperature

5oC ÷ 60oC (milieu); 5oC ÷ 40oC (surface)

Relative moisture

Maximum 85%

Completely drying time

7 days

Dew point

The substrate temperature and wet film must be at least 3°C above the dew point to avoid the risk of condensation or blister on the surface upon finishing.

ESTIMATED NORM

The covering system

Number of coatings

Consumption

Thickness

Normal coating

1 layer KKS® ELASTSEAL 332

1 layer KKS® ELASTSEAL 332

~ 0.60 kg/m2

~ 0.60 kg/m2

~0.8 mm

Standard coating

1 layer KKS® ELASTSEAL 332

1 layer KKS® ELASTSEAL 332

~ 0.90 kg/m2

~ 0.90 kg/m2

~1.2 mm

Coating with reinforcement layer

1 layer KKS® ELASTSEAL 332

The reinforcement layer

1 layer KKS® ELASTSEAL 332

~ 1.60 kg/m2

 

~ 0.80 kg/m2

~2.0 mm

 

WAITING TIME FOR NEXT COAT: Depending on temperature and humidity

Environmental conditions

Estimated time

+10oC/50% r.h

10 hours

+20oC/50% r.h

5 hours

+25oC/80% r.h

3 hours

+30oC/85% r.h

2 hours

STORAGE/ SHELF LIFE

KKS® ELASTSEAL 332 must be stored in a cool, dry and covered place. The temperature is about 5oC – 28oC. The product will react with humidity of the air as soon as the package is opened, so it should be used once. Under unopened packaging, not damaged at an average temperature of 25°C, the product has a shelf life of 12 months.

SAFETY INFORMATION

KKS® ELASTSEAL 332 may cause allergy, and should not be in direct contact with skin. When splashed in the eyes or on skin, wash immediately with plenty of water and seek medical advice if necessary. Product is non-toxic, non-flammable and non-hazardous in transportation. Disposal should be done according to local law. For more information, please refer to the latest Product Safety Data Sheet.

 

Related Products

View Detail
KKS® AQUASEAL 365
View Detail
KKS® AQUASEAL 360
View Detail
KKS® CRETESEAL C
View Detail
KKS® CRYSTASEAL 341
View Detail
KKS® ELASTSEAL 331
View Detail
KKS® HDPE-S MEMBRANE
View Detail
KKS® BITUMGARD PE
View Detail
KKS® EROSEAL 350
View Detail
KKS® HYPERSTOP DB
View Detail
KKS® LATEX 310
View Detail
KKS® LATEX 315
View Detail
KKS® WATERPLUG 302